I got a tech manual a few days ago and thought this would be useful information to post. I tried scanning the page but it was hard to read so I decided to make up my own using the manual as a guide. I hope it's not too confusing. ;-)
BigAl205
Complete OEM Audio Schematic for EX and SC (amplified)
I got a tech manual a few days ago and thought this would be useful information to post. I tried scanning the page but it was hard to read so I decided to make up my own using the manual as a guide. I hope it's not too confusing. ;-)
Attachments
I've been wondering that myself. It may be possible if I had the pin-outs of the bus cable.
When I had the OEM radio in, I listened to the XM some but I wasn't impressed enough to buy it. I listen to my Ipod more than anything.
Chew wan pinouts, mang? Chew gottem.
![Image]()
I've been wanting to try this, since I have a Pioneer, but I haven't been able to find a Pioneer cable. Don't forget, you'll have to sent remote turn on and continuous power, as well as ground on the factory plug to get this to work. I think, however, that since they're both made by pioneer, that it should work.
I've been wanting to try this, since I have a Pioneer, but I haven't been able to find a Pioneer cable. Don't forget, you'll have to sent remote turn on and continuous power, as well as ground on the factory plug to get this to work. I think, however, that since they're both made by pioneer, that it should work.
Here's a link to Majestic. I don't know if the one you need is prt #1 or 4.
http://www.hondaautomotiveparts.com...=ELEMENT&catcgry2=2007&catcgry3=5DR+EX+2WD&catcgry4=KA5AT&catcgry5=WIRE+HARNESS
http://www.hondaautomotiveparts.com...=ELEMENT&catcgry2=2007&catcgry3=5DR+EX+2WD&catcgry4=KA5AT&catcgry5=WIRE+HARNESS
I'll be putting a new head unit there but want to move the factory unit. I found a metra harness that I would use to install an aftermarket unit but it only has power and speaker wires and it's setup for the EX system with integrated amp. I need the end that matches the plug into the stereo too. Metra has that part number, but not all of the pins are there.
posting here cause i just woke up and my thread search and read limit seems to be around 3 (no but really ill keep looking, but i know someone *cough* like bigal would know this right away)
WHERE is the stock amp?
ive heard it is on the right side down by the stock sub? correct? if not please correct me
going to start pulling the E apart cause the speakers should be here in a few days
WHERE is the stock amp?
ive heard it is on the right side down by the stock sub? correct? if not please correct me going to start pulling the E apart cause the speakers should be here in a few days
This post has been deleted
Hey Al, you've got questions to answer here. What a great job in the charts.
Nice and clear. I don't understand much of it, but they're great.
Regards,
jurn
Nice and clear. I don't understand much of it, but they're great.
Regards,
jurn
remote
Any idea how the remote pin works with the 05-06 model which has pin one as the cd- and pin 2 as the cd+. Appears to not have the same set up as the other years. I tried remoting to pin one without effect , have now to try to remote to pin two but don't know what would hook up to pin one as the negative line to the remote( CD set up for the 06 model) I did look at the Motherboard of the Amp and found the pins 1 and 2 as pin one CD_ and pin2 as CD+
But what attaches to pin one CD-?
I shall try the harness connector with the blue lead that I am using from the Amp and then the CD+ remote from the outgoing harness from the HU.And see if this gives the necessary conductivity.
Any idea how the remote pin works with the 05-06 model which has pin one as the cd- and pin 2 as the cd+. Appears to not have the same set up as the other years. I tried remoting to pin one without effect , have now to try to remote to pin two but don't know what would hook up to pin one as the negative line to the remote( CD set up for the 06 model) I did look at the Motherboard of the Amp and found the pins 1 and 2 as pin one CD_ and pin2 as CD+
But what attaches to pin one CD-?
I shall try the harness connector with the blue lead that I am using from the Amp and then the CD+ remote from the outgoing harness from the HU.And see if this gives the necessary conductivity.
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
-
?
